The Homemade .22 Silencer: Threadmount

            To legally manufacture a silencer/sound suppressor in the United States, it is imperative that one submits an ATF Form 1 with fee, waits until it is approved, and receives the approved form with attached tax stamp, before any construction is started

The first cuts on this project will be taken on the thread mount, the “entrance” end cap on the silencer.  I’ll be cutting 17-4ph stainless steel, making an internal thread of 1/2″-28 with a tap, and using the single-point threading method on a machine lathe to cut the external thread of .900″-28tpi.  Once all that is done, I will apply a helical knurl and a slight roundover to the cap!

Let’s just start at the beginning!  So, I decided to just chuck up my sizable piece of stainless into my lathe and supported the end with a steady rest.  This is a little helper to keep longer pieces of stock rigid in the lathe when you’re working on one end of them.  It made more sense to me to use this method than to cut off a piece and try to figure out how to hold it in the lathe.  After facing off the end to be perfectly flat, I turned down the outside to .900″, the outer diameter of the threads we’ll cut to screw into the tube.  This cut was made to 1/2″ back from the end, and took several passes.  I utilized a carbide bit, which is an extremely hard material and great for this sort of thing.

22canthreadmount2 22canthreadmount3

Once that diameter was turned, a groove was required at the very end of the turned down area.  This groove will give our threads a place to end, avoiding the phenomenon sometimes noted with factory threaded items where the threads sort of just spread out into the shoulder, preventing a tight and smooth fit.   To make this groove, I’m using a thin parting blade.  This tool is thin with a square tip and is plunged straight into the workpiece for grooving operations like this, or as you’ll see soon, cutting off an entire section of the metal.  To help prevent binding, one trick I’ve used in my lathe is to hold the parting blade upside down and turn the workpiece in reverse.  Due to the type of cut made in the parting operation, there is a tendency to grab the work and cause the tool post to bind.  With this method, the tool and tool post can be pushed out of the way in the event of the workpiece grabbing the tool!

22canthreadmount4 22canthreadmount5

With the groove successfully cut to a depth of .860″, the next task was to drill and tap the inside of the mount.  With progressively larger drill bits, passes are made on the lathe until the tapping size for a 1/2″-28 hole, which I use a 29/64″ drill.  This is the part that screws onto the firearm so making sure it is a tight and straight thread is crucial.

22canthreadmount6 22canthreadmount7

Sharp drill bits were key in this; the stainless is machinable bit still very hard. Truth be told, the bits I had sharpened with my drill doctor just wouldn’t cut very well, so after touching the cutting edges up properly on a grinding wheel, they cut the material very easily. This was a small but valuable lesson to me in the importance of learning how to grind a drill bit versus buying a machine to do it for you.

22canthreadmount8

With the holes drilled, I used my adorably small boring bar to turn a taper on the inside portion of the bore.  This will of course be what faces towards the inside of the silencer tube, so this taper will assist the expansion of gasses, as well as reduce the overall weight of this individual piece.

22canthreadmount9

Tapping the mount for 1/2″-28 was probably the easiest thread cutting operation of the entire can.  I am lucky to have found a reasonably priced tap in this thread size,  so all that is required is putting the tap into the lathe, and turning the headstock by hand.  As expected, the tapped threads came out perfect and only took a few minutes of grunting as I turned the workpiece around the tap manually, with plenty of cutting oil of course.

Moving to the external threads that will screw into the tube, these won’t be quite as simple.  Cutting threads on the lathe, referred to often as the “single point method”, is one of the most important operations on a metal lathe.  The cutting tool is driven across the work at at the correct ratio to the work’s turning speed in order to make the specific helix required for the thread pitch.  28 threads per inch is a comparatively fine thread pitch, so the tool doesn’t move across quite as quickly, and the total depth of cut won’t be as deep as some other thread pitches.  There are a number of considerations to take in making the threading cut, multiple things that need to be given attention simultaneously, and it can be a nerve racking process, but I got through it relatively unscathed.

22canthreadmount10 22canthreadmount11

This next paragraph is a bit of an esoteric machining soliloquy. My shop note on accomplishing these threads was that it would have been more optimal do it by the numbers.  While there are a couple of different techniques that can be utilized in the single point process on the lathe, the most accepted one is to disengage the cutting tool from the lead screw (which is what is driving it across the workpiece) after each pass, back the cross slide off of zero away from the workpiece, reset the tool (like a typewriter) put the cross slide back on zero, advance the tool on the compound rest ever so slightly (to deepen the thread by .001″-.002″), then re-engage the lead screw when the rotation dial is in the right place.  This method is what every teacher and book recommends, and is what I should have done.  The method I used was one recommended to folks with smaller lathes or unsure of the tool rigidity, which I’ll admit I was unsure of to a degree.  Instead of disengaging the lead screw and backing the tool off, the lathe is simply reversed after being stopped at the end of each cut. I should note that this did work and the threads are perfectly smooth, true, and tight, but in this method, it left scratches on some of the threads and in my opinion made them uglier than necessary, despite still being functional.  That’s enough of my abstruse rant.

22canthreadmount12

Out of the metal turning frying pan and into the metal turning fryer; another operation that many machinists don’t exactly look forward to is parting.  As I was describing the parting tool earlier, we’re basically just going to cut the thread mount off of the long bar stock now.  I do that just by turning the work slowly, and driving the parting tool straight into the part.   It takes a while, especially with hard material such as this, but it works!

22canthreadmount13

And it leaves a cut surface needing only a small amount of touch up; I put the threaded portion of my newly minted part into some aluminum tubing to protect the threads from the chuck jaws, and turned the part around to face off what I’d just cut.

22canthreadmount14

And since I happen to have such a cute boring bar, I put an equally cute chamfer on the side of the threads that will be twisting onto a barrel.

22canthreadmount15

At this point the part is basically functional.  I took a file and ran it over the rear corner a number of times to give it a nice, round edge

22canthreadmount16

Then I put a gripping surface on the part, since this is where the whole silencer will be gripped when screwing it onto a gun.  I did this with a method I’ve been experimenting with that I refer to as a Helical Knurl.  I made a YouTube video about the process a few months ago.  Basically, the part is placed on the bolt that mounts the tool post (I used a custom bushing to make sure it fit snugly but could still rotate) and a large tap is mounted in the chuck and supported with a center in the tail stock on its other end.  The tap is turned by the lathe, as the part is slowly moved in on the tool post.  As the tap starts to cut, it will rotate the part.  After feeding the part in, it has a relatively deep series of vertical and slightly angled cuts that not only look unique, but also provide an easy to grip, concave surface.  I’ve done the more traditional forms of knurling, and I tend to prefer this one when I can get away with it.

22canthreadmount17

After a quick pass with a file and some emery cloth in the lathe to clean everything up, that’s the thread mount!

22canthreadmount18

The next part to be made will be the forward end cap, which will be made out of 7075 aluminum.  If you’d like to see some of these machining operations in action, you can check out the video I made:

Jeff

Jeff has been a firearms enthusiast for over 20 years. He is an NRA Certified Pistol Instructor, and a Kansas Concealed Carry Instructor. He also enjoys hunting, reloading, attending practical training courses, and does the majority of his own gunsmithing. Jeff maintains a small garage workshop which he shares in his YouTube channel, Practical Renaissance.

0 thoughts on “The Homemade .22 Silencer: Threadmount

  1. Chernobyl Episode 5 HBO. “Chernobyl”. HBO
    http://bitly.com/hboChernobylhttps://i.imgur.com/IDveTye.jpg

    Chernobyl..Episode~5//HBO….“Chernobyl”.**HBO.
    Chernobyl Episode 5 Episode 6 HBO. “Chernobyl”. HBO
    chernobyl hbo 5 episode 1 2 3 4 5 watch online

    http://bitly.com/hboChernobylhttp://bitly.com/hboChernobyl
    http://bitly.com/hboChernobylhttp://bitly.com/hboChernobyl
    http://bitly.com/hboChernobylhttp://bitly.com/hboChernobyl

    Chernobyl@Episode!!!5*HBO.**“Chernobyl”.!!HBO.
    Chernobyl Episode 5 Episode 6 HBO. “Chernobyl”. HBO

    Unforgotten on PBS, Chernobyl on HBO–wow, so good. There’s even a podcast to get more show notes and facts about what happened, a behind-the-scenes look. What We Do in the Shadows is just the best thing on TV right now for being funny. It’s a good time and it’s something I need right now. And a little bit of the NBA playoffs if I have time. Over the last few weeks we’ve seen Shazam! Made: fresh guacamole and pico de gallo for tacos, snickerdoodles for fun, and lots of stuff on the grill from asparagus to hamburgers and brats and Kabobs. His Loyal Dog by Ralph Hardy, The Widows of Malabar Hill by Sujata Massey, The Collected Schizophrenias: Essays by Esme Weijun Wang, and The Sense of Style: A Thinking Person’s Guide to Writing in the 21st Century by Stephen Pinker. Am looking forward to: G getting out of school for summer! It’ll be crazy but we both need the break. Camping Memorial Day weekend. It’s supposed to rain this weekend but if it lets up, I may plant a few more flowers this weekend. We’re also planning on seeing “Detective Pikachu” Sunday! Chernobyl Episode 5 watch online. It doesn’t shy away but it doesn’t overdo it in my opinion. The first two episodes have quite a bit of radiation sickness, and the third and fourth start to show the individuals who were in chernibyl at the time of the accident weeks later dying in a hospital. That is very graphic and difficult to watch. ’t want it watered down, also to respect those who actually went through those horrible things. The show is very tasteful but firm with reality imo. If you read Voices of Chernobyl, some of the stuff they describe, such as a man’s face just being “gone” from radiation burns wasn’t shown—just implied. It’s HBO, they have fantastic makeup people and pull no punches. You spend an episode in the hospital watching several people die. The rest of the episodes don’t show much radiation sickness beside a lot of people puking. Very. Radiation burns are accurately depicted so it’s literally ‘skin melting off’ graphic. It’s a really great show, but you’re gonna have a bad time based on your statement here.|Happy 100th episode, LOST! Did Eloise Hawking know that she would kill her son, Daniel? Why would that need to happen? What exactly is Eloise’s plan? To prevent Oceanic Flight 815 from crashing or to make sure that it all happens the same way it originally did? Is Daniel Faraday really dead? Who is Penny’s mother? What was Daniel Faraday doing in Ann Arbor? So, now we can change the future? What exactly are the rules? Can Radzinsky please kill himself already? If not, can someone do it for him? When will Marvin Candle lose his arm? How does Daniel know what’s going to happen? Was Daniel crying when he saw the Oceanic plane on the bottom of the ocean because he somehow remembers the island and the survivors? How does Charles Widmore know that the real Oceanic Airlines plane crashed on the island? Why doesn’t he tell Daniel that he’s his father? The latest leaks come after two major episodes of Game of Thrones season 7 were leaked early. These Game of Thrones episodes were S7 E4, called The Spoils of War, and S7 E6 Beyond The Wall. Both of these Game of Thrones episodes had hugely important plot points in it and game-changing moments for the narrative of the HBO fantasy epic. Season 1 Episode 4 or the Game of Thrones finale leaks early also. Season 1 Episode 4 has not leaked early. But if it does it’s likely to be posted on torrent download sites as well as illegal streaming services. And if that’s the case then Game of Thrones fans need to be aware of something very important. Security experts have warned that cybercriminals target pirated episodes of Game of Thrones the most. These illegal-to-download Game of Thrones episodes carry the highest risk of containing malware viruses. So if you’re trying to watch Game of Thrones through illicit means then it could leave your computer with a crippling piece of code. Mariya Fedorova, security researcher at Kaspersky Lab, said: “Other TV shows, such as Stranger Things, WestWorld and Orange is the New Black are not as popular as Game of Thrones. While Sean McGrath, editor of Game of Thrones, said: “These are exciting times for television fans. “Streaming services have shaken things up and we are living through a new golden age of TV programming. Arya Stark: Who has green eyes in Game of Thrones? Who will Arya kill? Chernobyl 6 Episode.
    This week he tried to pick up a girl, but he couldn’t be the funny guy, or just be himself. Instead, he was the hero saving the girl, the last thing you’d expect from Manny. I loved how he had to take off his shoes before entering the moon bounce. I still haven’t gotten to Fizbo, but this is Thanksgiving, and who the hell writes this much on Thanksgiving? Anyways, Fizbo was hilarious and Eric Stonestreet did a great job. ABC finished the night strong with the two-hour season finale of Dancing with the Stars (4.3) which hit a season high. CBS was way up from last week with NCIS (4.4), NCIS: Los Angeles (4.3), and The Good Wife (2.8). Despite the greatly improved lead-in, The Good Wife only managed to gain .2 from last week. NCIS: Los Angeles had a crossover episode with Pauley Perrette who plays Abby on NCIS. Chernobyl Episode 6 watch online.

    Chernobyl///Episode@@@5//HBO.=“Chernobyl”…HBO.
    Chernobyl Episode 5 Episode 6 HBO. “Chernobyl”. HBO

    Chernobyl***Episode!!!5**HBO./“Chernobyl”.//HBO.
    Chernobyl Episode 5 Episode 6 HBO. “Chernobyl”. HBO

    Chernobyl~Episode…5..HBO./“Chernobyl”.//HBO.
    Chernobyl Episode 5 Episode 6 HBO. “Chernobyl”. HBO

    Chernobyl//Episode@@@5///HBO..“Chernobyl”.@@@HBO.
    Chernobyl Episode 5 Episode 6 HBO. “Chernobyl”. HBO

    Chernobyl@@@Episode+5@HBO.~“Chernobyl”..HBO.
    Chernobyl Episode 5 Episode 6 HBO. “Chernobyl”. HBO

    Chernobyl@Episode//5+HBO.@“Chernobyl”.~HBO.
    Chernobyl Episode 5 Episode 6 HBO. “Chernobyl”. HBO

    http://www.bombjourthegame.com/viewthread.php?tid=22426#pid26562
    http://www.glitchforums.com/showthread.php?tid=58740&pid=1310074#pid1310074
    http://fdp-wilnsdorf.de/forum.php?newt=1&topic_id=3316650
    http://www.humboldtcannabisfarmers.com/viewtopic.php?pid=74485#p74485
    http://vansirc.net/forum/viewtopic.php?f=4&t=1519548
    http://med-unjfsc.edu.pe/foros/showthread.php?tid=160501
    http://change-everything.com/2018/06/14/5-ways-to-add-discipline-to-your-life-today/?unapproved=38792&moderation-hash=8cfbd5d685208ed44198f059b43d0963#comment-38792
    http://www.antropocrazia.com/forum/viewtopic.php?p=363426#363426
    http://forum.ibest.id/viewtopic.php?f=4&t=40084
    http://rp-pl.pl/showthread.php?tid=11&pid=139402#pid139402
    http://www.kingsraid.wiki/index.php?title=User:27.2.7.59
    http://beausaviary.mysidiahost.com/forum/showthread.php?tid=184769
    http://www.remify.app/foro/index.php?topic=397724.new#new
    http://confedesports.com/viewtopic.php?f=25&t=4550&p=200320#p200320
    http://forum.packbel.by/viewtopic.php?f=7&t=319258
    http://dinai.com/forum/viewtopic.php?f=4&t=177502
    http://mercadoforo.com/showthread.php?tid=7405
    http://legendofhunters.cba.pl/viewtopic.php?p=38001#38001
    http://www.see-game.hu/viewtopic.php?pid=653969#p653969
    http://bmworld.ru/showthread.php/112363-CHERNOBYL-chernobyl-hbo-5-episode?p=359462#post359462
    http://www.joenna.cc/bbs/viewtopic.php?pid=127871#p127871
    http://bbs.chinakaoyan.co/bbs/forum.php?mod=viewthread&tid=20145&extra=
    http://www.joenna.cc/bbs/viewtopic.php?pid=128108#p128108
    http://www.vietnamexpatsonline.com/viewtopic.php?f=4&t=489425
    http://whatisnormal.net/3-cara-bermain-idn-poker-online-pasti-menang-terus/?unapproved=8299&moderation-hash=ae373968b9b57e05f63d86b2ae9f92c3#comment-8299

Leave a Reply

Your email address will not be published. Required fields are marked *